- 1 Should you record vocals before mixing?
- 2 What does a mixer do for vocals?
- 3 How do professionals mix their vocals?
- 4 Should I mix vocals in mono or stereo?
- 5 What dB should vocals be at?
- 6 How loud should my vocals be in a mix?
- 7 Where should vocals sit in a mix?
- 8 How do you EQ vocals like a pro?
- 9 How do you mix vocals with a mastered beat?
- 10 How do you make vocals in punchy?
- 11 How can I eq my deep voice?
Should you record vocals before mixing?
Always record your vocals completely dry and add effects in the mixing stage. Always! The reason you want to record a dry signal, which means no time-based effects like reverb, delays, and echoes, is to keep your options wide open when you begin to mix.
What does a mixer do for vocals?
Mixing vocals is critical to creating a track that catches a listener’s attention. A great vocal can make or break a song. Creating the right conditions for the vocal to shine is why mixing is so important.
How do professionals mix their vocals?
In most genres, the vocals are the most important part of the mix. 10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
Should I mix vocals in mono or stereo?
If you record one vocalist, your vocals should be mono. However, if you record two vocalists or more or if you record in a room with unique acoustics, the vocals should be stereo. Moreover, recording vocals in mono makes them sound powerful, clear, and upfront.
What dB should vocals be at?
What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
How loud should my vocals be in a mix?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
How do you EQ vocals like a pro?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
How do you mix vocals with a mastered beat?
How to Mix Vocals to an Already Mastered Instrumental
- Step 1: Reduce the Output Volume of the Mastered Instrumental.
- Step 2: Set the Input Gain at the Correct Level.
- Step 3: Apply Effects/FX.
- Step 4: Mix Your Project.
- Step 5: Create the Final Master.
How do you make vocals in punchy?
A fast attack (5ms) will make your vocals sound thick and heavy. A slow attack (30ms) will make your vocals sound punchy and aggressive. Dial in a medium release time of 40ms and adjust from there. Try to get the compressor pumping in time with the music.
How can I eq my deep voice?
Applying EQ to a Voice Recording
- Use a High Pass Filter to Cut Everything Below 80Hz.
- Cut 100-300 Hz to Add Clarity.
- Cut 300-400 Hz if the Voice Sounds ‘Muddy’
- A Wide Boost Between 2-6 kHz Can Improve Clarity.
- Cut Around 3-5 kHz if the Voice Sounds too Sibilant.