Readers ask: How To Propeely Compress Rap Vocals?

How compressed should rap vocals be?

In short, the amount of compression. The more ratio you apply, the more compression takes place. Generally, in normal vocals 2:1 to 3:1 ratio is good to compress the upper dynamics. But when the vocal is aggressive you need to compress more.

How compressed should vocals be?

A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.

How much does rap vocals reduce?

It also ensures that the vocal sits better in the mix, and when the vocalist listens back during the recording session, they’ll feel more confident. So, aim for 2-6dB of gain reduction and a ratio below 3:1. Slow attack and release times tend to work best.

Should rap vocals be dry?

Using Delay Over Reverb The best way to mix rap vocals is to keep them relatively dry. We’re talking about mixing rap vocals that are aggressive and upfront in the mix. Traditionally, engineers will opt for delay instead of reverb to keep that vocal forward and present — not washed away in a sea of reverb.

You might be interested:  How To Get Rid Of P Sound In Vocals?

Should you compress or EQ first?

Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.

What is a good reverb setting for vocals?

Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.

How do I compress vocals like a pro?

This is how to compress vocals using a lighter, more musical approach:

  1. First of all, load up a compressor.
  2. Next, lower the threshold and raise the ratio to extreme settings.
  3. Start with a medium attack time around 15ms and adjust to taste.
  4. Dial in a medium release time of 40ms and adjust from there.

Should I use parallel compression on vocals?

Using parallel compression can be an effective way to give your vocals a professional edge but it’s a difficult technique to master. Use gates, EQ and de essers to remove content you don’t want to be harshly compressed.

Should you compress live vocals?

Live sound is largely correcting problems with subtractive EQ. Sure, it’s fun to roll off some of the top-end on your hall reverb, but don’t let that distract you from the things that actually need attention. Compression should be used sparingly. The lead vocals should be the center of your attention.

You might be interested:  Quick Answer: How To Fatten Vocals In Audacity?

How can I make my voice sound thicker?

Once you apply these ten techniques, your mixes as a whole will improve.

  1. Top-End Boost.
  2. Use a De’Esser.
  3. Remove Resonances.
  4. Control the Dynamics with Automation.
  5. Catch the Peaks with a Limiter.
  6. Use Multiband Compression.
  7. Enhance the Highs with Saturation.
  8. Use Delays Instead of Reverb.

What is the best compressor for rap vocals?

Top 10 Compressor Plugins for Hip Hop Vocals

  • Fabfilter Pro-C.
  • Eventide Ultrachannel.
  • Waves Renaissance Compressor.
  • Waves CLA-76.
  • McDSP 6030 Ultimate Compressor.
  • Waves V-Comp.
  • Logic Compressor.
  • Waves H-Comp.

How loud should vocals be in a mix?

Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.

What voice effects do rappers use?

The best vocal effects for rappers include de-essing, pitch shifting, time alignment, and parallel processing. Other great plugins that can help improve rap vocals include stutter and reverse effect, vocal delay throws, saturation, submixes, and distortion.

How can I make my rap vocals more aggressive?

Adding a subtle amount of distortion to a vocal track can really fill out the sound and make it loud and aggressive. Use a plugin that has a mix knob and increase it until you start to hear the vocals becoming distorted. At this point, back the distortion down a little bit.

Leave a Reply

Your email address will not be published. Required fields are marked *