- 1 Is it okay to record vocals in stereo?
- 2 Should vocals be in stereo or mono?
- 3 Can you pan a stereo track?
- 4 Should vocals be louder than the beat?
- 5 What happens when you record in stereo?
- 6 What dB should vocals be at?
- 7 What is a good EQ setting for vocals?
- 8 How do I make my vocals sound professional?
- 9 What is the difference between recording in mono or stereo?
- 10 Are condenser mic stereo or mono?
- 11 Should I pan left or right?
- 12 Should vocals be panned?
- 13 Does panning work in mono?
Is it okay to record vocals in stereo?
If you are recording the vocals of one singer in a booth, then you should record in mono. However, if you are recording vocals of multiple singers and instruments, you should record in stereo. The terms mono and stereo are quite common in the sound recording industry.
Should vocals be in stereo or mono?
Use the stereo field. The lead vocal should be in mono and central in the mix but the BVs can have as much width as you like. Keep it balanced, pan as many left as you do right.
Can you pan a stereo track?
The concept of panning is straightforward with mono tracks (as described above), but possibly less so with stereo tracks. Some DAWs feature two pan controls for each stereo track—one positions the left side of the signal, the other the right. Or you could partially-pan the stereo audio (e. g.
Should vocals be louder than the beat?
How loud should vocals be compared to instrumental. Vocals, especially the lead vocal should be louder than musical elements but a tad bit behind the drum transients in my opinion. But if you have an instrumental that has already been mastered and hyper-compressed which is often the case.
What happens when you record in stereo?
If you record in stereo, you’re using two microphones recorded to two different channels. Vocals and any direct-in instrument (ex. bass, electric guitar, keyboard) are recorded in mono. But you can still get a wider, stereo effect on something you’ve recorded in mono.
What dB should vocals be at?
What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
What is a good EQ setting for vocals?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
How do I make my vocals sound professional?
10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
What is the difference between recording in mono or stereo?
In short, a mono recording is one where the sound in the left and right channels is the same. A stereo recording has different sounds in each channel.
Are condenser mic stereo or mono?
Microphones convert sound waves to audio signals via mic capsules. Most mics have one capsule that outputs one signal, making them mono devices.
Should I pan left or right?
In recording, unlike theatre, left and right are always from the listener’s perspective. So if you pan to the left, the sound should come out of your left speaker. Pan to the right and it comes out of the right speaker. In an orchestral recording, the violins are on the right rather than the left.
Should vocals be panned?
The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. But as a general rule lead vocals should always be panned center.
Does panning work in mono?
“All mono tracks in a mix are to be left in the center of the mix with no panning and do not contribute to the width, space, or depth of the song. Mono tracks are only for kicks, bass, vocals and stuff like that.”