- 1 Should you stack lead vocals in a mix?
- 2 Where should lead vocals sit in a mix?
- 3 How do you EQ vocals like a pro?
- 4 How loud should vocals be in a mix?
- 5 What frequency do vocals sit?
- 6 How do you mix vocals with a mastered beat?
- 7 Is a condenser mic better for vocals?
- 8 Should I mix vocals in mono or stereo?
- 9 How can I eq my deep voice?
- 10 Are my vocals too loud in mix?
- 11 Should vocals be panned?
- 12 How do I make my vocals sound professional?
Should you stack lead vocals in a mix?
Use vocal stacking as an opportunity to support your lead vocal track – pushing it further toward the front of your mix. To reinforce your lead vocal, track doubles of the same part. Recording harmonies and background vocals that vary from the lead will add complexity to your mix without taking away from the lead.
Where should lead vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
How do you EQ vocals like a pro?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
How loud should vocals be in a mix?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
What frequency do vocals sit?
Male vocals will tend to have their fundamental frequencies between 100–300 Hz, while the fundamental frequencies of a female vocal will usually fall between 200–400 Hz.
How do you mix vocals with a mastered beat?
How to Mix Vocals to an Already Mastered Instrumental
- Step 1: Reduce the Output Volume of the Mastered Instrumental.
- Step 2: Set the Input Gain at the Correct Level.
- Step 3: Apply Effects/FX.
- Step 4: Mix Your Project.
- Step 5: Create the Final Master.
Is a condenser mic better for vocals?
Condenser microphones are best used to capture vocals and high frequencies. They are also the preferred type of microphone for most studio applications. Because of the thin diaphragm and increased sensitivity, condenser mics are often used to pick up delicate sounds. They also need a power source.
Should I mix vocals in mono or stereo?
If you record one vocalist, your vocals should be mono. However, if you record two vocalists or more or if you record in a room with unique acoustics, the vocals should be stereo. Moreover, recording vocals in mono makes them sound powerful, clear, and upfront.
How can I eq my deep voice?
Applying EQ to a Voice Recording
- Use a High Pass Filter to Cut Everything Below 80Hz.
- Cut 100-300 Hz to Add Clarity.
- Cut 300-400 Hz if the Voice Sounds ‘Muddy’
- A Wide Boost Between 2-6 kHz Can Improve Clarity.
- Cut Around 3-5 kHz if the Voice Sounds too Sibilant.
Are my vocals too loud in mix?
If you find that the vocals suddenly go from sounding too low in the mix to too loud, then you need to apply more dynamic processing. Vocals with wildly uncontrolled dynamics are a hallmark sign of an amateur mix engineer.
Should vocals be panned?
The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. But as a general rule lead vocals should always be panned center.
How do I make my vocals sound professional?
10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.