- 1 What level should I mix vocals at?
- 2 Should I mix vocals with the beat?
- 3 Should you mix before vocals?
- 4 Should Beat be louder than vocals?
- 5 Where should vocals sit in a mix?
- 6 Do you master before or after vocals?
- 7 How do you add vocals to a mastered beat?
- 8 How do you professionally mix and master vocals?
- 9 What vocal effects do singers use?
- 10 How do you record vocals without distortion loud?
- 11 How do you EQ vocals like a pro?
- 12 How do you blend vocals with music?
What level should I mix vocals at?
You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
Should I mix vocals with the beat?
If you are just putting out a tape to grab exposure then placing vocals over a mastered beat is fine. If you’re planning to release a debut album then I would suggest mixing the beat with the vocals. You will be able to blend the vocals better with the instruments.
Should you mix before vocals?
mix whatever you consider the most important first. I usually start with making a “bed” for the vocals from a pad, guitar, bass, kick etc and then make the lead vocals sit on top of that.
Should Beat be louder than vocals?
Should Vocals be Louder than the beat? No and Yes! Well it depends on the genre and style you are mixing or what the song calls for. What you don’t want is a vocal poking out like a sore thumb in your song.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
Do you master before or after vocals?
Mastering before the vocals are necessary so you don’t have to go back and rework a song after vocals have been overdone or vocals are flat. Mastering before the vocalists work will enable you to hear their parts and determine whether they are perfect for the mix. The mixing process is also very important.
How do you add vocals to a mastered beat?
How to Mix Vocals to an Already Mastered Instrumental
- Step 1: Reduce the Output Volume of the Mastered Instrumental.
- Step 2: Set the Input Gain at the Correct Level.
- Step 3: Apply Effects/FX.
- Step 4: Mix Your Project.
- Step 5: Create the Final Master.
How do you professionally mix and master vocals?
10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
What vocal effects do singers use?
The options available for vocal effects are broad. They include reverb, delay, choir, distortion, compression, gain automation, de-essing, EQ, pitch shift, and echo.
How do you record vocals without distortion loud?
Another way you can tackle loud vocals is not to record directly into the microphone, another alternative you might want to try is backing away from the microphone and recording a bit far from it or you could simply turn your microphone a tad bit away from your mouth or input audio source.
How do you EQ vocals like a pro?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
How do you blend vocals with music?
How To Mix Vocals
- First, place the element (vocal) in the stereo field.
- Then, cut out unnecessary frequencies with an equalizer.
- Then, if applicable, enhance with a compressor.
- Then, if necessary, boost frequencies with an equalizer.
- Then, if necessary, send to reverb bus or other effect bus.