Question: How Loud Should Music Be With Vocals?

Should vocals be louder than the music?

Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.

How many dB should my song be?

I recommend mixing at -23 dB LUFS, or having your peaks be between -18dB and -3dB. This will allow the mastering engineer the opportunity to process your song, without having to resort to turning it down.

What level should vocals be in a mix?

Here’s how loud your vocals should be in a mix: Your vocal level should be lower than the drums, but louder than the instrumentation.

Should Kick be louder than snare?

The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.

You might be interested:  Often asked: How To Record Good Vocals In Ableton?

Where should vocals sit in a mix?

Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.

What dB should your 808 be?

Just make it loud in the context of the mix. Start with all your faders down. Bring up the 808 so it’s at a reasonable level in your DAW (probably somewhere around -18 dBFS ). Then, bring in all of the other instruments around it.

What dB to use for mastering?

Most mastering engineers recommend having the loudest part of a mix at –5 dB from absolute ‘0’ dBFS. This means you should have the loudest section of the mix 5 dB lower before the peak level of ‘0’.

How loud is Spotify master?

You should leave at least 1 dB of headroom. Though Spotify recommends mastering louder tracks to −2 dB true peak.

Should I mix vocals in mono or stereo?

If you record one vocalist, your vocals should be mono. However, if you record two vocalists or more or if you record in a room with unique acoustics, the vocals should be stereo. Moreover, recording vocals in mono makes them sound powerful, clear, and upfront.

Should vocals be panned?

The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. But as a general rule lead vocals should always be panned center.

You might be interested:  Quick Answer: What Is The Best Microphone For Recording Vocals On Computer?

Should vocals be in mono or stereo?

Use the stereo field. The lead vocal should be in mono and central in the mix but the BVs can have as much width as you like. Keep it balanced, pan as many left as you do right.

Are my vocals too loud in mix?

If you find that the vocals suddenly go from sounding too low in the mix to too loud, then you need to apply more dynamic processing. Vocals with wildly uncontrolled dynamics are a hallmark sign of an amateur mix engineer.

Why do my vocals sound so bad?

If your vocals are recorded in a bad room, it’s extremely obvious by the end of the mix. Room reflections can also cause compression and pitch correction to sound unnatural. It’ll make the vocals sound “fake,” like they were tacked on at the end of the mix.

How do you fix loud vocals?

Try watching this video on www.youtube.com, or enable JavaScript if it is disabled in your browser.

  1. Understand The Problem.
  2. Use a De-Esser to Tame Harsh Frequencies.
  3. Use a Narrow EQ to Cut Harsh Frequencies.
  4. Use a Focused Dynamic EQ.
  5. Use Clip Gain and Volume Automation to Manually Reduce Volume.

Leave a Reply

Your email address will not be published. Required fields are marked *