- 1 Should you use compression on vocals?
- 2 What does a compressor do on vocals?
- 3 How much compression should I use on vocals?
- 4 Does compression make vocals louder?
- 5 Do rappers double their vocals?
- 6 How loud should vocals be in a mix?
- 7 Should you EQ or compress first?
- 8 What is a good reverb setting for vocals?
- 9 What is the best compressor for vocals?
- 10 What level should I record vocals?
- 11 How do I make my vocals louder?
- 12 What does too much compression sound like?
Should you use compression on vocals?
It evens out the often-erratic levels that a singer can produce and tames transients that can cause digital distortion. You can use compression on vocals to just even out the performance and to create an effect. If you use a compressor to even out a vocal performance, you don’t want to hear the compressor working.
What does a compressor do on vocals?
Simply, a compressor is used to compress a sound’s dynamic range. That is, to make the louder and quieter parts of the sound’s performance closer to each other in level. It does this in one of two ways. In “downward compression,” the compressor attenuates the signal when it gets too loud.
How much compression should I use on vocals?
A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.
Does compression make vocals louder?
One of the most effective tools at your disposal for crafting consistent vocals is compression. When combined with automation, compression can make your vocals sound loud, punchy, and modern.
Do rappers double their vocals?
Rappers and singers have traditionally recorded vocal doubles (informally called “vocal dubs”) on the ending phrases every bar or half a bar..
How loud should vocals be in a mix?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
Should you EQ or compress first?
Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.
What is a good reverb setting for vocals?
Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.
What is the best compressor for vocals?
The Best Vocal Compressors for Studio-Quality Audio
- Avalon. VT-737SP. A go-to for professional pop, R&B, & rap studio recordings.
- Warm Audio. WA76. This limiting amplifier is designed to affordably emulate the classic UA 1176, which is nearly impossible to find these days.
- FMR Audio. Really Nice Compressor.
What level should I record vocals?
You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
How do I make my vocals louder?
Once you apply these ten techniques, your mixes as a whole will improve.
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
What does too much compression sound like?
When you compress too hard with fast attack times, the dynamic range of your mix is squashed. You’ll end up with something that sounds like this: A song with no room to breathe; as flat as a pancake.