- 1 Should I mix vocals with the beat?
- 2 How do you mix vocals over a mastered beat?
- 3 Do you mix before or after vocals?
- 4 What level should my vocals be?
- 5 Should I record over a mastered beat?
- 6 How loud should my beat be before vocals?
- 7 How do professionals mix their vocals?
- 8 What dB should vocals be in a mix?
- 9 Should Kick be louder than snare?
- 10 Where should vocals sit in a mix?
- 11 Should vocals be mono or stereo?
Should I mix vocals with the beat?
If you are just putting out a tape to grab exposure then placing vocals over a mastered beat is fine. If you’re planning to release a debut album then I would suggest mixing the beat with the vocals. You will be able to blend the vocals better with the instruments.
How do you mix vocals over a mastered beat?
How to Mix Vocals to an Already Mastered Instrumental
- Step 1: Reduce the Output Volume of the Mastered Instrumental.
- Step 2: Set the Input Gain at the Correct Level.
- Step 3: Apply Effects/FX.
- Step 4: Mix Your Project.
- Step 5: Create the Final Master.
Do you mix before or after vocals?
When you are mixing your beat, you need to leave room for your vocals. Basic physics says that two things cant occupy the same space. So, no two similar sounds can be in the same place on the mix which is where panning and levels come in. So your hats and mid to high freq sounds can’t be in the same place.
What level should my vocals be?
What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
Should I record over a mastered beat?
Since the track that you have is mastered, you can still record over it but the vocals would have to get mixed and then mastered separately from the beat and then blend back together.
How loud should my beat be before vocals?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
How do professionals mix their vocals?
In most genres, the vocals are the most important part of the mix. 10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
What dB should vocals be in a mix?
If you mix them too loudly, they will stick out. What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB.
Should Kick be louder than snare?
The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
Should vocals be mono or stereo?
Should you record vocals in mono or in stereo? If you are recording the vocals of one singer in a booth, then you should record in mono. However, if you are recording vocals of multiple singers and instruments, you should record in stereo. The terms mono and stereo are quite common in the sound recording industry.