- 1 What is a good compression ratio for rap vocals?
- 2 How much compression should I use on vocals?
- 3 How much does rap vocals reduce?
- 4 What dB should rap vocals be at?
- 5 Should you compress or EQ first?
- 6 Do rappers double their vocals?
- 7 Should I use parallel compression on vocals?
- 8 Should you always use compression on vocals?
- 9 What is a good reverb setting for vocals?
- 10 What is the best compressor for rap vocals?
- 11 How do you set EQ for vocals?
- 12 Should vocals be louder than bass?
- 13 What dB level should I mix at?
- 14 Where should vocals sit in a mix?
What is a good compression ratio for rap vocals?
Generally, in normal vocals 2:1 to 3:1 ratio is good to compress the upper dynamics. But when the vocal is aggressive you need to compress more. So you have to increase the ratio up to 7:1. Probably, you would find the sweet spot anywhere 5:1 to 6:1.
How much compression should I use on vocals?
A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.
How much does rap vocals reduce?
It also ensures that the vocal sits better in the mix, and when the vocalist listens back during the recording session, they’ll feel more confident. So, aim for 2-6dB of gain reduction and a ratio below 3:1. Slow attack and release times tend to work best.
What dB should rap vocals be at?
What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB. This is to keep an even balance on the level of the vocals without distortion.
Should you compress or EQ first?
Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.
Do rappers double their vocals?
Rappers and singers have traditionally recorded vocal doubles (informally called “vocal dubs”) on the ending phrases every bar or half a bar..
Should I use parallel compression on vocals?
Using parallel compression can be an effective way to give your vocals a professional edge but it’s a difficult technique to master. Use gates, EQ and de essers to remove content you don’t want to be harshly compressed.
Should you always use compression on vocals?
When used correctly, compression is a key ingredient for vocals that sound professional, modern and radio-ready. When used incorrectly, compression can quickly ruin a good vocal recording and make your music sound amateur and over-processed.
What is a good reverb setting for vocals?
Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.
What is the best compressor for rap vocals?
Top 10 Compressor Plugins for Hip Hop Vocals
- Fabfilter Pro-C.
- Eventide Ultrachannel.
- Waves Renaissance Compressor.
- Waves CLA-76.
- McDSP 6030 Ultimate Compressor.
- Waves V-Comp.
- Logic Compressor.
- Waves H-Comp.
How do you set EQ for vocals?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
Should vocals be louder than bass?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
What dB level should I mix at?
I recommend mixing at -23 dB LUFS, or having your peaks be between -18dB and -3dB. This will allow the mastering engineer the opportunity to process your song, without having to resort to turning it down.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.