- 1 Should vocals be panned center?
- 2 Should panned vocals be mono or stereo?
- 3 Where should background vocals be panned?
- 4 What is center panned audio?
- 5 Where should vocals sit in a mix?
- 6 How do you equalize vocals?
- 7 Should vocals be louder than the beat?
- 8 Is stereo better than mono?
- 9 Are condenser mic stereo or mono?
- 10 How loud should background vocals be in a mix?
- 11 Should backing vocals be panned?
- 12 How can I make my voice sound thicker?
- 13 Should Bass be panned?
- 14 How do I convert audio from hard panned to center panned?
Should vocals be panned center?
The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. But as a general rule lead vocals should always be panned center.
Should panned vocals be mono or stereo?
If you are recording the vocals of one singer in a booth, then you should record in mono. However, if you are recording vocals of multiple singers and instruments, you should record in stereo. The terms mono and stereo are quite common in the sound recording industry.
Where should background vocals be panned?
If you have several background tracks, you’ll want to pan them away from the center. This will create space for your vocal to live in. How much you pan your BGVs is up to you. It depends on the song and your own taste.
What is center panned audio?
Panning is the spread of a monaural signal in a stereo or multi-channel sound field – it is critical to the make up of the stereo image. Figure 1 – Mixer pan controls. Usually, the most problematic area of the sound field is the center, as this is normally the busiest place within a mix.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
How do you equalize vocals?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
Should vocals be louder than the beat?
How loud should vocals be compared to instrumental. Vocals, especially the lead vocal should be louder than musical elements but a tad bit behind the drum transients in my opinion. But if you have an instrumental that has already been mastered and hyper-compressed which is often the case.
Is stereo better than mono?
Stereo isn’t necessarily better than mono. Stereo sounds wider, more detailed, and more realistic. However, depending on where it’s played, stereo sometimes creates phase cancellation issues that make it sound hollow, empty, and weird. Stereo is recommended when your listening environment is normal.
Are condenser mic stereo or mono?
Microphones convert sound waves to audio signals via mic capsules. Most mics have one capsule that outputs one signal, making them mono devices.
How loud should background vocals be in a mix?
Adjust the fader on the group buss until the backing vocals sit nicely underneath the lead vocal. They shouldn’t be anywhere near as loud as the lead vocal part, but should still be clearly audible.
Should backing vocals be panned?
It depends on how you whant the backing vocals to sound. I suggest you try hard panning two of them and have the other two halfway to each side. This way you get the width but it will sound more solid and cohesive across the stereo image.
How can I make my voice sound thicker?
Once you apply these ten techniques, your mixes as a whole will improve.
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
Should Bass be panned?
Always pan the bass center If the bass comes from both stereo speakers, it can be louder than if it only comes from one. Also, in the days of vinyl records, there could be problems with mistracking on playback if the bass was panned all the way to one side.
How do I convert audio from hard panned to center panned?
Add a Utility audio effect to the audio track containing the hard-panned audio file. In Utility´s Channel Mode menu, select “Left” or “Right” so the audio plays back through both speakers. Use the “Freeze Track” then the “Flatten Track” – commands from the Edit menu to create a new center-panned audio file.