- 1 How do you use reverb on vocals?
- 2 Should I record vocals with reverb or add after?
- 3 Should I use reverb or delay?
- 4 Is Plate reverb best for vocals?
- 5 Does reverb make you sound better?
- 6 How do professionals mix their vocals?
- 7 What dB should vocals be in a mix?
- 8 How do you balance vocals in a mix?
- 9 Which is better echo or reverb?
- 10 Do I need both delay and reverb pedals?
- 11 Is echo same as reverb?
- 12 What type of reverb is best for vocals?
- 13 What is the best reverb for live vocals?
- 14 What effects to add to vocals?
How do you use reverb on vocals?
Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb. The following example shows a dual-reverb setup.
Should I record vocals with reverb or add after?
Vocals should always be recorded dry. Meaning that there are no time based effects such as reverb and delay on the track when you record. This is due to the fact that adding these effects would hide performance issues when tracking resulting in poor recordings that would need to be re recorded.
Should I use reverb or delay?
Reverb can give a guitar a fuller sound. Delay can be used on a guitar for effects which permit the player to play less but sound like they are playing more. Reverb and delay are terrific signal processing effects which can sculpt a sound to fit the need.
Is Plate reverb best for vocals?
Plate reverb works well on many vocals for a couple of reasons. First, you usually want your vocal to cut through the mix. Plate reverb’s bright tone boosts the presence of the vocal, helping it cut through more easily. Second, the slightly unnatural sound of a plate can help the vocal feel unique.
Does reverb make you sound better?
When you “normally” sing, you don’t just sing in a dead room (or just inside your head), you hear at least some natural reflections and resonances. So reverb adds the illusion of these reflections and resonances and subsequently sounds more natural to your ears.
How do professionals mix their vocals?
In most genres, the vocals are the most important part of the mix. 10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
What dB should vocals be in a mix?
If you mix them too loudly, they will stick out. What dB should vocals be recorded at? You should record vocals at an average of -18dB for 24-bit resolution. The loudest parts of the recording should peak at -10dB and be lowest at -24dB.
How do you balance vocals in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
Which is better echo or reverb?
A reverberation can occur when a sound wave is reflected off a nearby surface. An echo is usually clear and can be easily distinguished because of the distance and time the sound wave travels. Adding sound absorption in a space will reduce the reflections and cause the sound waves to decay at a faster rate.
Do I need both delay and reverb pedals?
If you just want a fuller sound for recording and live purposes, and your amp doesn’t feature reverb (or has a poor quality one, which is quite common), then the reverb pedal is your best bet. If, however, you want to be more experimental, or just want to make your solos sound cool, then go for the delay pedal.
Is echo same as reverb?
Reverberation is the persistence of sound after the sound source has been stopped. It results from a large number of reflected waves which can be perceived by the brain as a continuous sound. On the other hand, an echo occurs when a pulse of sound can be heard twice.
What type of reverb is best for vocals?
But I still want to add some brightness, plate reverb is going to be good for that. And in general, that’s why plate reverb works well on vocals. Now, let’s go back to the idea of short decay times, because shorter decay times also work well on vocals, because we don’t want to make the vocal go too far back in the mix.
What is the best reverb for live vocals?
Hall reverb is the most popular type of reverb, especially for vocals. It is intended to simulate the audio effect generated in the large hall. In real life, the large hall has a long decay.
What effects to add to vocals?
The options available for vocal effects are broad. They include reverb, delay, choir, distortion, compression, gain automation, de-essing, EQ, pitch shift, and echo.