- 1 Should my vocals be louder than the beat?
- 2 What dB should vocals be at Reddit?
- 3 What dB is best for mic?
- 4 What is a good EQ setting for vocals?
- 5 Should Kick be louder than snare?
- 6 Where should vocals sit in a mix?
- 7 Are my vocals too loud in mix?
- 8 How loud should instrumentals be?
- 9 What level should I record audio at?
- 10 Is EQ necessary on vocals?
- 11 Is a condenser mic better for vocals?
- 12 What is the best EQ setting for bass?
Should my vocals be louder than the beat?
How loud should vocals be compared to instrumental. Vocals, especially the lead vocal should be louder than musical elements but a tad bit behind the drum transients in my opinion. But if you have an instrumental that has already been mastered and hyper-compressed which is often the case.
What dB should vocals be at Reddit?
6 db is standard, give more if the incoming signal is more unpredictable. Most preamps add increasing amounts of noise to your recording the higher you adjust the gain. Stay below the value where noise becomes audible, even if that means recording at less than -6 db.
What dB is best for mic?
16-19 dB-A is good enough for most purposes. You may hear some noise when you record relatively quiet instruments, but it’s usually unobtrusive. 20-23 dB-A is a pretty high self-noise figure for a studio microphone.
What is a good EQ setting for vocals?
Best EQ Settings for Vocals
- Roll off the low-end starting around 90 Hz.
- Reduce the mud around 250 Hz.
- Add a high shelf around 9 kHz & a high roll off around 18 kHz.
- Add a presence boost around 5 kHz.
- Boost the core around 1 kHz to 2 kHz.
- Reduce sibilance around 5 kHz to 8 kHz.
Should Kick be louder than snare?
The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.
Where should vocals sit in a mix?
Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.
Are my vocals too loud in mix?
If you find that the vocals suddenly go from sounding too low in the mix to too loud, then you need to apply more dynamic processing. Vocals with wildly uncontrolled dynamics are a hallmark sign of an amateur mix engineer.
How loud should instrumentals be?
I usually find 6 dB to be enough, but there are some particularly loud beats that have required more. The first thing you should do is get the vocals sounding solid. If you have a lot of clients bringing you instrumentals to track over, creating a vocal mixing template is the best way to go.
What level should I record audio at?
According to Pike, your audio level should stay on the negative side of the number scale and never go above 0. Anything above this results in distortion, which will make your audio torture to listen to. He suggests keeping your level at around -10 to -12, but this can vary depending on your project and your subject.
Is EQ necessary on vocals?
Although the methodologies by which mix engineers sweeten their vocals can vary to some degree—particularly in terms of gear choice and the order in which they apply certain processing—most top mixers would agree that the EQ is one of the most essential tools necessary to sculpt out a great-sounding vocal.
Is a condenser mic better for vocals?
Condenser microphones are best used to capture vocals and high frequencies. They are also the preferred type of microphone for most studio applications. Because of the thin diaphragm and increased sensitivity, condenser mics are often used to pick up delicate sounds. They also need a power source.
What is the best EQ setting for bass?
On Android, I prefer to use PowerAmp, and it has one of the best equalizer settings, including stereo/mono setup.