FAQ: How To Compress Vocals Ableton?

How do I compress my singing voice?

This is how to compress vocals using a lighter, more musical approach:

  1. First of all, load up a compressor.
  2. Next, lower the threshold and raise the ratio to extreme settings.
  3. Start with a medium attack time around 15ms and adjust to taste.
  4. Dial in a medium release time of 40ms and adjust from there.

How do I make my voice sound better on Ableton?

Put your vocals to the mix, take away a little bit of bass, add a frequencies at the high end of the EQ – you’ll hear that this makes the vocals cut out better and gives the vocals more presence. Hopefully what you hear now is a good-sounding vocal, but still a bit thin and lonely.

Should you compress or EQ first?

Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.

Should you compress live vocals?

Live sound is largely correcting problems with subtractive EQ. Sure, it’s fun to roll off some of the top-end on your hall reverb, but don’t let that distract you from the things that actually need attention. Compression should be used sparingly. The lead vocals should be the center of your attention.

You might be interested:  Often asked: Tyga "taste" Background Vocals Who Sings?

Does Ableton have autotune?

Auto-TuneĀ® Pro, Auto-Tune Artist, Auto-Tune EFX+, and Auto-Tune Access are all compatible with Ableton Live 10.1 on both Mac and Windows. Auto-Tune EFX+ and Auto-Tune Access are compatible with Ableton Live 9.77 (64-bit) and later on both Mac and Windows.

Is Ableton good for vocals?

You might not think it, but Live works brilliantly for recording, processing, and organising vocals, including harmonies, which is what we’re mostly talking about here.

Does Ableton Live 10 have autotune?

You can use Ableton Live for autotuning your vocal tracks with free virtual studio technologies (VSTs). By downloading pitch correction VSTs and inserting them into your VST folder, you can then drag them onto the audio tracks in your Ableton Live audio project and autotune your vocal tracks in under five minutes.

What goes first EQ or crossover?

EQs and other devices should always be in Line before the actual Crossover. Most DSP Units offer Input EQ which is essiantially that.

Do you EQ every track?

Traditional EQ is great for fixing problems that remain consistent throughout the entire track. But when you’re dealing with problems that change over time, it isn’t the best option. For issues like these, try multiband compression or dynamic EQ. These tools will often produce better results.

What is a good EQ setting for vocals?

Best EQ Settings for Vocals

  • Roll off the low-end starting around 90 Hz.
  • Reduce the mud around 250 Hz.
  • Add a high shelf around 9 kHz & a high roll off around 18 kHz.
  • Add a presence boost around 5 kHz.
  • Boost the core around 1 kHz to 2 kHz.
  • Reduce sibilance around 5 kHz to 8 kHz.
You might be interested:  How To Down Pitch Vocals In Ableton Live?

What is a good compression ratio for vocals?

A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.

What is a good reverb setting for vocals?

Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.

Leave a Reply

Your email address will not be published. Required fields are marked *