- 1 How do you not over compress vocals?
- 2 Should you use compression on vocals?
- 3 What is a good compression ratio for vocals?
- 4 How do professionals mix their vocals?
- 5 Should vocals be louder than the beat?
- 6 Should you compress or EQ first?
- 7 How much compression do you need for pop vocals?
- 8 Do rappers double their vocals?
- 9 What is a good reverb setting for vocals?
- 10 What is the best compressor for vocals?
- 11 How do you do multiband compression on vocals?
How do you not over compress vocals?
You want the vocal to be at roughly the same level every word—don’t worry if it sounds over-compressed in solo. Drop the fader down (on the new channel) and bring the volume back up until you notice the vocal becoming louder. Then, back off the volume a touch. You only want it to be subtle.
Should you use compression on vocals?
It evens out the often-erratic levels that a singer can produce and tames transients that can cause digital distortion. You can use compression on vocals to just even out the performance and to create an effect. If you use a compressor to even out a vocal performance, you don’t want to hear the compressor working.
What is a good compression ratio for vocals?
A good starting point for a rock vocal would be a 4:1 ratio with a medium-fast attack and a medium release. Then, set the threshold for around 4 to 6dB of gain reduction. Increase or decrease the attack time until you get the right level of forwardness for the mix.
How do professionals mix their vocals?
In most genres, the vocals are the most important part of the mix. 10 Ways to Make Vocals Sound Modern & Professional
- Top-End Boost.
- Use a De’Esser.
- Remove Resonances.
- Control the Dynamics with Automation.
- Catch the Peaks with a Limiter.
- Use Multiband Compression.
- Enhance the Highs with Saturation.
- Use Delays Instead of Reverb.
Should vocals be louder than the beat?
How loud should vocals be compared to instrumental. Vocals, especially the lead vocal should be louder than musical elements but a tad bit behind the drum transients in my opinion. But if you have an instrumental that has already been mastered and hyper-compressed which is often the case.
Should you compress or EQ first?
Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.
How much compression do you need for pop vocals?
For most pop, rap, and rock-based genres you’re going to squash the vocals a lot more than you expect, especially due to the mixes being denser. So, for dynamic compression, start with a 5:1 ratio and explore going higher, even up to an 8:1 ratio, depending on the threshold.
Do rappers double their vocals?
Rappers and singers have traditionally recorded vocal doubles (informally called “vocal dubs”) on the ending phrases every bar or half a bar..
What is a good reverb setting for vocals?
Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.
What is the best compressor for vocals?
The Best Vocal Compressors for Studio-Quality Audio
- Avalon. VT-737SP. A go-to for professional pop, R&B, & rap studio recordings.
- Warm Audio. WA76. This limiting amplifier is designed to affordably emulate the classic UA 1176, which is nearly impossible to find these days.
- FMR Audio. Really Nice Compressor.
How do you do multiband compression on vocals?
Once you know the range, remove the EQ and load up a multiband compressor. Bypass all of the multiband ranges until you are only targeting the problematic frequency range. Apply 2-3dB of compression using similar settings to your main compressor, with one important exception—don’t apply any makeup gain.