FAQ: How Much Reverb On Background Vocals?

Should background vocals have reverb?

As well as reducing their volume for lead support, you want to place them in a reduced frequency range, just as you would any instrument in your mix. The lead vocal would be good with a short reverb time while the backing vocals can be blended together with a longer reverb like a Hall reverb. Compress them.

How much reverb should I use on vocals?

Move the pre-delay to about 30-40% or so as a starting point and see how it sounds. With your EQ, maybe set the high-pass around 200Hz and the low-pass at about 12kHz. In a situation like this, you may want to have more body in the reverb.

How loud should background vocals be?

Adjust the fader on the group buss until the backing vocals sit nicely underneath the lead vocal. They shouldn’t be anywhere near as loud as the lead vocal part, but should still be clearly audible.

How do you make vocals sound like they’re in the background?

Wrapping Up: Mixing Background Vocals

  1. Create a BGV master bus.
  2. Copy over the plugins from your main vocal and check for any issues.
  3. Reverse the boosts and cuts from the main vocal’s tonal EQ.
  4. Increase the compression until you are getting 5-10dB’s of gain reduction.
  5. Pan your BGVs to create space for the main vocal.
You might be interested:  Question: How To Mix Beat And Vocals?

Where should background vocals sit in a mix?

Background vocals should sit somewhere underneath the leads in terms of volume. There’s no one-mix-fits-all dB amount to go by, but you should definitely be thinking in terms of quieter backgrounds and louder leads.

How do you push vocals back in the mix?

Tip #1 – Here’s a top notch trick to get your vocals to sit on top of the mix nicely. Send everything but the vocals to their own aux, and apply a very subtle compressor (only a few dB’s reduction). Side chain the lead vocals to this compressor. This will dip the track by a 2 or 3 dB’s every time the vocals come in.

Is Plate reverb best for vocals?

Plate reverb works well on many vocals for a couple of reasons. First, you usually want your vocal to cut through the mix. Plate reverb’s bright tone boosts the presence of the vocal, helping it cut through more easily. Second, the slightly unnatural sound of a plate can help the vocal feel unique.

Why do singers use reverb?

When you “normally” sing, you don’t just sing in a dead room (or just inside your head), you hear at least some natural reflections and resonances. So reverb adds the illusion of these reflections and resonances and subsequently sounds more natural to your ears.

What vocal effects do singers use?

The options available for vocal effects are broad. They include reverb, delay, choir, distortion, compression, gain automation, de-essing, EQ, pitch shift, and echo.

Should background vocals be mono or stereo?

If you record one vocalist, your vocals should be mono. However, if you record two vocalists or more or if you record in a room with unique acoustics, the vocals should be stereo. Moreover, recording vocals in mono makes them sound powerful, clear, and upfront.

You might be interested:  How To Record Good Vocals?

Should you pan vocals?

The best way to give your mix a solid core is to keep lower frequency sounds in the center. That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. But as a general rule lead vocals should always be panned center.

What are background vocals called?

Alternative terms for backing vocalists include backing singers, backing vocals, additional vocals or, particularly in the United States and Canada, backup singers or sometimes background singers, or harmony vocalists.

How do you equalize vocals?

Best EQ Settings for Vocals

  1. Roll off the low-end starting around 90 Hz.
  2. Reduce the mud around 250 Hz.
  3. Add a high shelf around 9 kHz & a high roll off around 18 kHz.
  4. Add a presence boost around 5 kHz.
  5. Boost the core around 1 kHz to 2 kHz.
  6. Reduce sibilance around 5 kHz to 8 kHz.

Leave a Reply

Your email address will not be published. Required fields are marked *